A Little Fixer Up’er

I made a series of sun-catchers for family members one year, and this little hummingbird was one of them.  Sadly, he got squished and his wings fell off!  *sad face*  So as something I can do to finish a variety of projects I started (before moving on to new ones), I thought I would work on fixing up this sun-catcher with some improvements!  I talked about some of the steps I could take to fix this piece in an earlier post, and here they are in more detail and with pictures.

Step One:  Removing the broken wings.  Luckily the glass isn’t broken – the copper foil has just been pulled off the edges of the glass.  To remove the wings, I pulled them off with my hands, breaking the copper foil to remove them from the pieces.  {Just a note – use your judgement when doing this.  If it will pull other solder seams or otherwise make more trouble for you to fix, just melt everything off gently with the soldering iron.}  Then I melted the solder in the joint between the wing and body, using the soldering iron to push the remaining foil out of the way.

IMG_7243

Step Two:  Remove the old copper foil from both wing pieces.  I used a small exacto knife to help me scrape the copper foil off all edges of the wings.

IMG_7246

Step Three:  Cleaning the glass.  There is a sticky residue left over from the copper foil around the edges of the wing pieces.  To clean them, I put them into a sink of warm water with a small amount of dish soap.   I let the soak for a few minutes, then used an old rag to wipe off the sticky stuff on the edges of the glass.  Good as new and ready to be re-foiled and attached back on!

Sticky residue on edges of glass

Step Four: Re-apply copper foil.  I’m using a 1/4″ copper foil, partly because I’m out of 7/32″ and partly because I want there to be a solid border around these wing pieces.  Going to 3/16″ is not a great option for single pieces that will be attached by only a single solder joint.

Foiled wings

Step Five: Attaching the wings back onto the body.  I thought about why these wings came off in the first place, and a lot of it has to do with the fact that there isn’t a whole lot of structural connectivity between the body and the plane of the wing.  It was very easy for the wing to be bent upwards or downwards, and for the copper foil to pull away from the glass.  So I’m going to use some thin wire to help create more stability.  I’ve started incorporating wire supports into my work to add structural integrity and strength, so I think it’s not a bad idea here.  I’m going to bring a piece of wire from the middle line of the body across the front edge of the wing, and the same thing on the back – a piece of wire running from the middle seam of the body across the back edge of the wing.

Step Six: Soldering it all together.  This process takes some time, and it would be amazing if I had a third hand to keep it all together.  If you’re thinking about getting into stained glass, be prepared to constantly cut and burn your fingers.  The first step to make this process much easier was to apply a layer of solder on all edges of the wings separately before adding wire or attaching them to the body of the hummingbird.

I chose to solder the wire all the way around the wings, both because it created a more consistent line around the wings, and just adds strength, which is the point of this fix.  I spot-soldered the wire first and then went over it again to add a smooth edge.

The last steps in reattaching the wings were to attach the wire to the body joint, and then to cover it all with a heavy line of solder.  This is where the earlier step of applying a thin coat of solder all the way around the edges really helps out – the goal now is to create joints between the existing solder instead of trying to get into some really tight spaces with a soldering iron to get everything coated.

Step 7: Clean the piece and VOILA!  Good as new!

IMG_7331

IMG_7322

Advertisements
Tagged , , , , , , , , , , ,

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s

%d bloggers like this: